![]() Note: The -debug binary informs the user of an incorrect license. Where XXXXX-XXXXX-XXXXX-XXXXX-XXXXX is your license key. Tips and tricks Entering the Workstation Pro license key From terminal # /usr/lib/vmware/bin/vmware-vmx-debug -new-sn XXXXX-XXXXX-XXXXX-XXXXX-XXXXX # ln -s wssc-adminTool /usr/lib/vmware/bin/vmware-wssc-adminTool To prevent the service startup, this can be fixed with a symlink: The rvice calls wssc-adminTool in its command chain, despite having been renamed to vmware-wssc-adminTool. ![]() PIDFile=/var/lock/subsys/vmware-workstation-server ![]() etc/systemd/system/rvice ĮxecStart=/etc/init.d/vmware-workstation-server startĮxecStop=/etc/init.d/vmware-workstation-server stop Wants=rviceĪfter=rviceĮxecStart=/usr/bin/vmware-networks -startĪdd this service as well, if you want to connect to your VMware Workstation installation from another Workstation Server Console: WantedBy=multi-user.target /etc/systemd/system/rvice ĮxecStop=/usr/bin/vmware-usbarbitrator -kill service files ( vmware-usbarbitrator and vmware-networks are also included vmware-workstation AUR with a few differences): (Optional) Instead of using /etc/init.d/vmware ( start|stop|status|restart) and /usr/bin/vmware-usbarbitrator directly to manage the services, you may also use. See the INSTALL document found on the repository for the most up-to-date module installation instructions for VMware Workstation versions from 12.5.5 and up. The older versions presented in this article and their natively supported kernels are as follows: 15.5 (kernels up to 5.4), 14.1.7 (4.18) and 12.5.9 (4.12).įor VMware bundle versions, a collection of patches needed for the VMware host modules to build against recent kernels can be found from the vmware-host-modules GitHub repository. VMware Workstation 16.0 supports kernel 5.8 out of the box. If it loads for too long without response, please try #Cannot load module vmmon. rvice for sharing virtual machines (not available since version 16).rvice for connecting USB devices to guest.rvice for guest network access (otherwise you will get an error could no connect 'ethernet 0' to virtual network and you will not be able to use vmware-netcfg).Then, as desired, enable some of the following services: It is also necessary to install the appropriate headers package(s) for your installed kernel(s): for example linux-headers or linux-lts-headers.įor vmware-workstation AUR, start rvice first to generate /etc/vmware/networking. Install vmware-workstation AUR, vmware-workstation16 AUR, vmware-workstation15 AUR, vmware-workstation14 AUR, vmware-workstation12 AUR or vmware-workstation11 AUR for respectively versions 17, 16, 15, 14, 12 and 11 of VMware Workstation. ![]() If it shows Unable to install all modules, please try #Cannot load module vmmon. If the guest needs to reach the Internet, run the following command to verify Internet access: ping 85.12.30.Tip: To (re)build the modules from terminal later on, use:.To verify that the network interface is up and has an IP address, run one of the following commands: ip addr or ifconfig.Add a network adapter of type NAT, unless it already exists.I can connect from the guest to the outside via an interface configured for NAT, but I can only connect from the host to the guest after I have clicked Save in the Virtual Network Editor This appears to be a bug in VMware Workstation 12.x and probably previous versions. Even if you did not make any changes, click Save.If you do not have a NAT network, click Add Network to create it.Check whether you have a virtual network of type NAT.To start the Virtual Network Editor as root, run the following command: sudo /usr/bin/vmware-netcfg.Assuming that you are using VMware Workstation, perform the following steps and checks: ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |